This project is for all of you who do not sew but like to have decorative fabric treatments and accessories around your house to add color, pattern, and style.
I made the sewn version of the chair back covers back in the Spring – many of you liked them, but told me you didn’t have a sewing machine and asked it I could write a post on how to make them the no-sew way.
Now that I am decorating for Fall, I changed the chair back covers to bold black and white stripes. I wanted to warm things up. I chose the horizontal stripe because it is a classic and will look nice anytime of the year. I made them without making a single stitch – the easy no –sew way.
I found the fabric online at the OnlineFabricStore. I have become an online fabric shopping junkie. I have found the best deals are online and they have every color, pattern, and style in one place, I don’t have to run all over town looking for fabric inspiration. The downside, you can’t actually touch and feel the fabric to see the colors and size of the repeat. If you like to see the fabric in your hand before buying, you can order a sample for $1.
suppliesneeded:Fabric – I used Premier Prints Vertical Black/White Fabric I needed 3 1/2 yards of fabric to make 6 chair back covers. See how to measure your chairs below. Ribbon to coordinate with fabric – I used 48” of ribbon to make 4 – 12” ties for each chair Fabric glue – my fave is Beacon Fabri-Tac, but any fabric glue will work. You can find fabric glue at any craft or fabric store. Iron and ironing board Tape measure Scissors Straight pins
To figure out yardage needed:
Measure back width of chair x back height of chair x 2 (front and back) and add 2 inches to these measurements for hem/finished edge allowance.
- The back width of my chair was 16”, the back height – 24”. I added 2 inches to the 16” width. I doubled the 24” height to 48” and added 2 inches.
- For each chair I needed to cut my fabric 18”wide x 50” long. Optional: I added 6 more inches to the height/length of my measurement since I wanted the back to hang longer than the front.
- Keep in mind the way the stripes or your fabric pattern runs before ordering and cutting fabric.
*** Wash fabric before cutting so shrinkage will occur before you cut.
Cut fabric to size.
To make finished edges for each cover -Fold over all sides, 1/2-inch and press. Fold over all sides again another 1/2” and press.
Determine where on your chair you want the ties to be. You will need four, two on each side – front and back. Mark placement with a straight pin. Cut ribbon into 4 – 12” pieces.
When the cover is finished and tied on, it will look like the illustration below.
How to Attach Ribbon to Sides of No Sew Chair Back Cover
1. Remove pin for one ribbon tie placement. Add a dab of glue under and on top of one end of ribbon. Place end of ribbon under fold.
2. Add a dab of glue under fold and on top of ribbon. Fold fabric fold over it and press with fingers to adhere.
3. Bring ribbon across fold.
4. Glue down with a dab of glue. Let dry.
5. Ribbon section that goes over the fold should have glue under it and look like photo. Repeat steps for each tie.
6. Once each ribbon tie is in place, run a line of glue under the rest of the fold all around the cover.
7. Press with your fingers to smooth and adhere fabric to glue. Repeat on all sides.
8. Press each cover and place over chair and tie on.
Covers can be washed normally after 24 hours. Do not dry clean.
I like to use this type of cover on my dining room chairs because they are so versatile and give me lots of seasonal options for change.
I can tie them on over a bare chair as shown in the tutorial.
Or without a tie over my existing white chair slipcovers , as well as tuck the backs into the knotted back of the white slipcover.
Quick and easy no sew chair back covers add a lot of impact for little time and cost – my kind of project. I wish stripping the chairs would be as easy.
Online Fabric Store sent me my choice of fabric to make the chair back covers. All words and opinions are my own.Pin It