| |

How to Make a Restoration Hardware Concrete Fire Column

This Post May Contain Affiliate Links. Please Read my Disclosure Policy.

Knock Knock…Hack Hack… that is what I have been doing the past few days to create a trio of knock-off Restoration Hardware Concrete Fire Columns. I was inspired by this one I saw in the Restoration Hardware catalog.

I immediately was reminded of the building tubes I used to use to set up store displays and knew I could inexpensively make my own DIY version of one of these concrete fire columns. Here is the RH version.

Restoration Hardware Concrete Fire Columns

Here are the three I made – they are not eco-friendly gel fueled, just plain ole candlelight fueled.


I sit out on my patio in the autumn a lot as it is my FAVORITE time of year. I wanted to get it all ready for the season by adding some ambiance in the evening when I like to go outside, relax on the chaise with a cup of tea and warm dessert and stargaze into the autumn sky.

Trio-of-DIY-Restoration-Hardware concrete candle columns for outdoors.

Restoration Hardware also has a tabletop version.  That was the easiest one to make.

  • Tabletop Fire Column TIP: Glue a round of felt to the bottom so you won’t scratch your table.
Restoration-Hardware-Table with concrete fire column on top.

The hardest part of the entire project is picking up the 80 pound bag of concrete. I had my hubby help me with that.  I bought the rocks at the Dollar Tree.

Knock-off-Restoration-Hardware Concrete Fire Column

The tall glass hurricane is from Michaels. The two smaller ones I picked up at my local thrift store.


When I was buying the stones at the Dollar Tree I also picked up a little bit of Autumn Pixi-Dust in the way of some fake autumn leaves in hopes that the magic of Autumn is soon upon us and the heat of this summer is a thing of the past.


How To Make a Knock Off of a Restoration Hardware Concrete Fire Column

supplies needed:

  • 1 Quick Tube – they sell them in the building supplies areas at home improvement stores. Cost about $8.  I used an 8” diameter one that was about 4’ high
  • 2  – 80 pound bags of  Commercial Grade Quikcrete.  This was enough to make all three.   This mix has less stones in it and will produce a much smoother surface than the other mixes.  Look for the green and white bag.
  • Big mixing bucket – I used a 5 gallon paint can that they sell at Lowes.
  • Stirring stick – I used a leftover piece of PVC pipe, but a 2 x 4 would work
  • Water
  • Gloss paint any color – I used spray paint
  • Piece of plywood or a plastic drop cloth
  • Level
  • Coffee Can
  • Rubber gloves
  • Eye and nose protection
  • Box cutter
  • Sanding block and coarse sandpaper

Preparing the Cardboard Tubes

1.  The cardboard building forms look like this. They come in many different diameters. I used an 8” one.  Make sure you are getting one that is at least 1 –inch wider than the glass hurricane you plan to use to put on it.


 2.  Figure out how tall you want each column.  I gauged mine on the height of my chaise and then cut the other two in  half size of each other.   The smallest one can go on a table by itself when you want candle light for dining.


 3.  The directions from QuikCrete said to use a release agent when you want to remove the cardboard tube. The guy at Home Depot told me they didn’t sell it, but told me to spray some gloss paint inside the tube and let it dry. The gloss surface would make it easier to remove the tube when the concrete was dry. 


4. Make sure the top and bottom of your cut tubes are level.


5.  I then made a bottom for each tube using a foam plate. I used duct tape to secure each plate to the bottom of each cut tube.


6.  I then placed the tubes on a big piece of plywood I had.  Make sure the surface you place the tubes on is level.  You don’t want leaning towers of Pisa.  The plywood or plastic drop cloth is to protect the surface you are working on from the concrete.


Mixing the Concrete

1. This step is the hardest only because the 80 pound bag of concrete is hard to move.  Get your bag of concrete right next to your mixing bucket.  Fill the bucket with 2- 1/2 quarts of water. Put on a pair of rubber gloves to protect your hands – then use a scoop ( I used a plastic container) to slowly add half the bag of concrete to the water in the bucket.


2.  Mix it gradually and make sure you stir it well before adding more mix.  Do not add the whole bag you will never be able to stir it!  Add slowly a little bit of mix, stir etc. The directions on the bag say to  wear safety glasses and one of those little white masks as you add the mix to the water. The mix is very fine and you don’t want to get it in your eyes or lungs.

You can add a bit more water if needed to get a nice smooth consistency.


3. Once you like the consistency, use your scoop to add the concrete to the tube. Push the PVC pipe into the tube once it is 1/3 of the way filled to make sure you are packing the concrete in and getting rid of any air pockets.  Keep filling and pushing the PVC pipe until the tube is filled.  If you run out of concrete mix.  Start another batch and then continue to fill the tubes.


4.  To make the indent for the glass hurricane to fit in – press a coffee can into the top. This coffee can just happened to be the perfect size.  You may have to find something that is a bit wider than the hurricane you are going to use.

Center it and gently push down.   This will make some of the concrete come out. You want the coffee can down at least 1/2”  – 1”.


5.  Smooth around the can with your gloved finger until it is smooth getting rid of the excess that has spilled out.  Gently rotate the can a few times to make sure the concrete on the sides of it are not going to dry to the column.  As the column dries repeat rotating the can during the first few hours of drying time to ensure it doesn’t become a permanent part of the column.

Let The Concrete Dry


1.  After a few hours you can remove the can. It will look like this. Let the column dry at least for 24 hours or longer depending on how humid the air is.


Remove Cardboard Tube

1.  Once the column is dry – use a box knife to cut away the cardboard tube from the column.  Spray it with a hose if needed to help you remove the tube.  Mine came off easily.


2. Tip the column to the side to remove the plate from the bottom.


3.  The excess concrete along the bottom edge will come off easily with sandpaper.


Sand Edges of Concrete Column to Smooth

1. Put coarse sandpaper on a sanding block and go over the top surface to smooth.


2.  You can also use the sandpaper to get rid of any ridges along the bottom and sides of the column as well as any paint or cardboard that might have stuck. It comes right off with the sandpaper.


3. Place your glass hurricane on top.


It is still very hot here, but…


…I am hoping the Dollar Tree Pixi-Dust I bought does its magic soon.


Crisp cool nights under a blanket gazing at the stars…


Ahhhhh….Bliss xo Autumn

Concrete Fire Column DIY Outdoor Lighting
How to make a concrete candle holder for backyard lighting

Leave a Reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.


  1. Wow that was a lot of hard work! I’m tired just hearing about it! They look spectacular and you should really enjoy sitting out on the deck admiring them..I know I would!

  2. Holy AWESOMENESS Diane!!! I want those and a glass of wine and some great music – all by sitting by a nice fire outside. Incredible work!